2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness

Fits RT, RT-S, SE5 and SM5 Models with trailer quick connect wiring harness 4 flat pins trailer connection. Manufacture with solid steel and Powder Coated in semi-gloss black. The Hitch comes with the side plates that once installed will remain on the Spyder but allows an easy removal and re-installation of the hitch. It is predrilled to accept a 1 7/8″ or 2″ Ball. There are 2 holes for the security chains or steel cables. We use Canada Post services. RS-GS-ST And RT Hitch Installation Instructions. Do not change the belt alignment. Use a floor jack to take the weight off the rear wheel. Remove the plastic cover on each side of the axle. Remove the cutter pin on the right side. Unbolt the axle and remove it completely. You can use a rubber hammer to start sliding it out. Take the washers off on each side and replace them with the side plates. Note there is a left and right side. Re-install the axle and bolt it in place. Once this is done, insert the cutter pin and re-install the plastic cover on the nut. Bolt in place the U-Shape hitch using the hardware included in the box. Insert the bolt from the inside out and once it is bolted in place, install the plastic nut cover. Bolt the bracket (ball holder) in place and make sure to center it with the center of the wheel. It would be better to have someone helping you when re-installing the axle. One that pulls on the wheel and the other one that slides the axle back in place. Don’t change the belt alignment. RS-GS-ST et RT Instructions. Utiliser un crick pour enlever le poids sur la roue arrière. Enlever les couvercles de plastiques de chaque côté de l’essieu. Enlever la cutter pin sur le côté droit. Enlever l’essieu complètement. Enlever les washers de chaque côté et remplacer avec les side plates. Notez qu’il y a un côté gauche et un côté droit. Ré-insérer l’essieu, et ne pas oublier de remettre la cutter pin. Ré-installer les couvercles de plastique. Boulonner en place l’attache remorque avec les boulons fournis dans la boite. Boulonner en place la bracket qui reçoit la boule. Bien la centre avec le centre du pneu. N’oubliez pas d’enlever le frein à main pendant l’installation. Ne pas changer l’ajustement de la courroie. L’installation se fait mieux à deux personne lors de la ré-insertion de l’essieu. Une personne tire sur la roue et l’autre glisse l’essieu. Merci pour votre achat. The item “2010-17 Can-Am Spyder RT Trailer Tow Hitch With Wiring Harness” is in sale since Wednesday, July 27, 2016. This item is in the category “eBay Motors\Parts & Accessories\Motorcycle Accessories\Other Motorcycle Accessories”. The seller is “traileretc” and is located in Notre-Dame-des-Prairies, Quebec. This item can be shipped worldwide.
  • Surface Finish: Powder Coated Black
  • Part Brand: Trailer ETC
  • Country of Manufacture: Canada
  • Part Type: Accessories
  • Make: Trailer ETC
  • Country/Region of Manufacture: Canada
  • Type: Trailer Hitch Wiring Harness
  • Manufacturer Part Number: TH-001-WH
  • Brand: Trailer ETC
  • Warranty: Yes
  • Placement on Vehicle: Rear

Comments are closed.