Ford 5.0 EFI Speed Density universal wiring harness 1985-1992

Ford 5.0 EFI Speed Density universal wiring harness 1985-1992

Sensor (NOT MAF) into your Cobra kit car, Muscle car, Street rod, Truck, 4×4, etc. You must use an ECM (sequential injector firing) from one of the Cars listed. The Truck/Bronco ECM (batch injector firing) is different and will. The Truck engines will have to replace your remote TFI distributor with a TFI attached distributor and mount 2 Oxygen sensors in the exhaust (Truck O2 sensor will not work). There are 3 versions of this harness (Throttle body on Passenger side, Throttle body on Drivers side and Truck/Bronco). Once every injector and sensor is plugged in, you will have 3 wires to hook up. Feed, Ignition feed and ground. It is built in the. With brand new OEM Ford connectors, 260 degree automotive grade GXL wire (thicker insulation than TXL wire). Harness can be used with long tube headers or stock exhaust manifolds. Harness is designed to mount the ECM under the dash (42 inches of wire from the back of the motor). Harness can be used with 5 speed manual, AOD, or any Non-computer controlled transmission. EGR eliminator is included and comes pre-installed. About the only upgrade you can add to the motor is Headers and exhaust improvements. If you wanted to change the. Heads, aftermarket intakes, throttle bodies, etc; I would not use this harness, the ECM cannot compensate for changes as well as a MAF system. This harness is made for the H. Firing order/Cam (1-3-7-2-6-5-4-8), but can be changed for Non-H. System includes: complete instructions, an assortment of 300 degree F wire loom, harness wrap and zip ties (not bare wire like other harnesses) to give it a finished look and protection. Manufactured by the Detail Zone (a division of Ron Francis Wiring) with RJM Technology. These are built right with quality parts from the correct manufacturers and quality checked for performance. Circuits are tested to assure quality. The item “Ford 5.0 EFI Speed Density universal wiring harness 1985-1992″ is in sale since Monday, July 01, 2013. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Chester, Pennsylvania. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, South africa, New Zealand.
  • Placement on Vehicle: Front
  • Warranty: Yes
  • Country of Manufacture: United States
  • Brand: The Detail Zone
  • Manufacturer Part Number: Cobra-75SD

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM

6.0L Diesel Engine Wire Harness & Sensors is a direct fit for the following. 2004 Ford F-250 Super Duty 2004 Ford F-350 Super Duty 2004 Ford F-450 Super Duty 2004 Ford F-550 Super Duty -With Build Dates After 9/23/2003 Without Fuel Heater. Genuine Ford Part Number: 4C3Z-12B637-CA. The item “04 Ford F250 F350 Super Duty 04-05 Excursion 6.0L Diesel Engine Wire Harness OEM” is in sale since Wednesday, December 02, 2015. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Engines & Components\Other”. The seller is “quirkparts” and is located in Quincy, Massachusetts. This item can be shipped worldwide.
  • Brand: Ford
  • Manufacturer Part Number: 4C3Z-12B637-CA
  • Other Part Number: 4C3Z12B637CA
  • Placement on Vehicle: Front
  • Surface Finish: Wiring Harness
  • Warranty: 2 Year
  • Product Notes: With 6.0L Engines / Without Fuel Heater
  • Primary Color: Black
  • Model: F-250 F-350 F-450 F-550 Super Duty Excursion
  • Year: 2004 2005
  • Make: Ford

Incoming search terms:

  • engine wiring harness for 1976 F250

Ford 2.3 Turbo EFI wiring harness 1983-1988

Ford 2.3 Turbo EFI wiring harness 1983-1988

It’s also a good replacement for a factory equipped Ford 2.3L Turbo vehicles as well. This harness is emissions compliant for an OBD-I system. When this harness is used with an 1987/88 Turbo Coupe ECM, it has circuits for electric fans, fuel pump, diagnostic port, water temp/oil pressure and alternator. You will be required to use a 1987-88 Ford Thunderbird Turbo Coupe heated Oxygen sensor with this harness. Once every sensor is plugged in, you will have 3 wires to hook up (Battery feed, Ignition feed and ground). It is built in the U. With brand new OEM Ford connectors, 260 degree automotive grade GXL wire (thicker insulation than TXL wire). Harness can be used with a long tube header or stock exhaust manifold. Harness is designed to mount the ECM (48 inches from the back of the motor) under the dash. Harness can be used with 5 speed manual, or any Non-computer controlled transmission. It will work with any performance upgrades or engine diagnostic tool designed for the Ford 2.3L Turbo engine. System includes: complete instructions, an assortment of 300 degree F wire loom, harness wrap and zip ties (not bare wire like other harnesses) to give it a finished look and protection. Manufactured by the Detail Zone (a division of Ron Francis Wiring). The item “Ford 2.3 Turbo EFI wiring harness 1983-1988″ is in sale since Friday, April 24, 2009. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Blacksburg, Virginia. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, South africa, New Zealand.
  • Warranty: Yes
  • Country of Manufacture: United States
  • Brand: The Detail Zone
  • Manufacturer Part Number: MG-65

Ford 5.0 EFI Mustang/Bronco wiring harness 1989-1993

Ford 5.0 EFI Mustang/Bronco wiring harness 1989-1993

It is designed to plug into the original Ford body harness or aftermarket body harness with 3 wires. It is built in the U. With brand new OEM Ford connectors, 260 degree GXL wire (quality automotive fireproof wire with thicker insulation than TXL wire), 300 degree corrugated wire loom, and 1200 degree fiberglass loom around the exhaust. The harness is properly fused with quality relays. Can be used with long tube headers or stock exhaust manifolds. Harness is designed to mount the ECM (30 inches from the back of the motor) under the dash. It’s pre-wired for Air Conditioning or On-Board-Air compressor. Harness can be used with 5 speed manual, AOD, or any Non-computer controlled transmission. EGR eliminator comes pre-installed. It will work with any performance upgrades or engine diagnostic tool designed for the Mustang 5.0L engine. This harness is made for the H. Firing order/Cam (1-3-7-2-6-5-4-8), but can be changed for Non-H. System includes firewall grommet and complete instructions. Manufactured by the Detail Zone (a division of Ron Francis Wiring) with RJM Technology. These are built right with quality parts from the correct manufacturers and quality checked for performance. Circuits tested to assure quality. The item “Ford 5.0 EFI Mustang/Bronco wiring harness 1989-1993″ is in sale since Friday, April 24, 2009. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Blacksburg, Virginia. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, South africa, New Zealand.
  • Warranty: Yes
  • Country of Manufacture: United States
  • Brand: The Detail Zone
  • Manufacturer Part Number: Bronco-75

Ford 5.0 EFI universal wiring harness 1989-1993

Ford 5.0 EFI universal wiring harness 1989-1993

Please specify the year, make and model of the car the engine came from. Once every sensor is plugged in, you will have 3 wires to hook up (Battery feed, Ignition feed and ground). It is built in the U. With brand new OEM Ford connectors, 260 degree automotive grade GXL wire (quality automotive fireproof wire with thicker insulation than TXL wire). This harness is properly fused with quality relays. Harness can be used with long tube headers or stock exhaust manifolds. Harness is designed to mount the ECM under the dash (42 inches of wire from the back of the motor). Harness can be used with 5 speed manual, AOD, or any Non-computer controlled transmission. EGR eliminator is included and comes pre-installed. It will work with any performance upgrades or engine diagnostic tool designed for the Mustang 5.0L engine. This harness is made for the H. Firing order/Cam (1-3-7-2-6-5-4-8), but can be changed for Non-H. System includes: complete instructions, an assortment of 300 degree F wire loom, harness wrap and zip ties (not bare wire like other harnesses) to give it a finished look and protection. Manufactured by the Detail Zone (a division of Ron Francis Wiring) with RJM Technology. These are built right with quality parts from the correct manufacturers and quality checked for performance. Circuits tested to assure quality. The item “Ford 5.0 EFI universal wiring harness 1989-1993″ is in sale since Saturday, November 15, 2014. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Blacksburg, Virginia. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, South africa, New Zealand.
  • Warranty: Yes
  • Country of Manufacture: United States
  • Brand: The Detail Zone
  • Manufacturer Part Number: Cobra-75

Ford 4.6/5.4 EFI wiring harness kit Telorvek design

Ford 4.6/5.4 EFI wiring harness kit Telorvek design

This harness is for the engine and transmission wiring for a Ford 4.6L. It will allow you to wire the engine and transmission when installing them into a earlier model vehicle like Cobra kit cars, Muscle cars, Street rods, Trucks and 4×4, etc. This is not a factory replacement wiring harness. This harness is an EEC-V OBD II system designed to use the original Ford 4.6L ECU. (not included with this kit). Will have to be reprogrammed to remove PATS anti-theft at a minimum. The picture represents the items you will get, but some items may be different. Each of these items is specific and we want to include the correct wiring. We cannot build the kit until the questions have been answered. With this harness you can design where to mount your ECU and the routing of each wire custom to your vehicle. This harness allows you to mount the computer up to 20 feet (in Trunk, under seat, behind kick panel inside the vehicle) away from each sensor. The computer plugs-in 18 inches from the stainless steel Telorvek panel used as a junction between the computer and sensors that contains the fuses, relays and check engine light. There is an additional wire for mounting the check engine light on your dash. You will get a bag for each sensor with a wired sensor connector and 20 feet of wire. Each wire is printed where it is coming from and going to every 10 inches. You plug in each sensor and run the wires back to a terminal block on the Telorvek panel, cutting the excess wire and crimping a fork terminal. Place the numbered wire with terminal under the numbered screw and tighten the screw. Once every sensor and fuel pump is wired and plugged in, you will have 3 wires to hook up (Battery feed, Ignition feed and ground). This harness is built in the U. With brand new OEM Ford connectors and 260 degree automotive grade GXL wire (thicker insulation than TXL wire). The harness includes OEM diagnostic port for Ford 4.6L. The harness can be used with long tube headers or stock exhaust manifolds. It can be used with 5 speed, 6 speed, 4R70W, 4R100W (wiring included when used) or any non-computer controlled transmission typically installed behind this motor. It will work with any performance upgrades or engine diagnostic tool designed for the Ford 4.6L engine you are using. Wiring for all emissions sensors are included in this kit if you request them. Emissions wiring can easily be eliminated for off-road vehicles. These are built right with quality parts from the correct manufacturers and quality checked for performance. The item “Ford 4.6/5.4 EFI wiring harness kit Telorvek design” is in sale since Friday, February 03, 2012. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Chester, Pennsylvania. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, South africa, New Zealand.
  • Warranty: Yes
  • Country of Manufacture: United States
  • Brand: The Detail Zone
  • Manufacturer Part Number: MK-97A