FORD Premium Stereo Radio Wire Harness w Steering Control CAN-BUS/ RAP/ VSS/ RSE

FORD Premium Stereo Radio Wire Harness w Steering Control CAN-BUS/ RAP/ VSS/ RSE

FORD Premium Stereo Radio Wire Harness w Steering Control CAN-BUS/ RAP/ VSS/ RSE

Our competition has come and gone, and many have had user names removed because of bad business practices. We are dedicated to your business. FORD Premium Stereo Radio Wire Harness w Steering Control CAN-BUS/ RAP/ VSS/ RSE. THX / RAP / MSCAN Radio Replacement & Steering Wheel Control Interface. WORKS WITH THESE MAKE MODELS BELOW ONLY. This Harness interface: allows the replacement of a factory radio in select Ford vehicles with MSCAN databus radios. Using this interface will retain factory features such as. Steering wheel controls (SWC). Rear seat entertainment (RSE). Rear Seat Controls (RSC) and the THX or Sony amplifier when the original radio is removed. Harness: also provides data bus driven outputs such as. Retained accessory power (RAP). Vehicle speed sensor (VSS). Reverse trigger and parking brake. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the vehicle 2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to flash 4 times. RSC & LCD buttons that are identical to the SWC will mimic the SWC one for one. All other buttons cannot be programmed. The LED will flash whenever a SWC button is pressed. RSC must be set to AUX mode to pass audio to aftermarket radio. Vehicles equipped with a factory amplified system must disconnect SYNC if they wish to use the voice button. Not disconnecting SYNC will result in the rear speakers muting every time the voice button is pressed. Basically Does not retain SYNC. Check our other listing for the SYNC version 7. Feeding too strong of an audio signal into the headrest monitors will cause the audio output to shut down. If this happens you must turn the tv off and on and lower the audio signal. Data controlled accessory and navigation outputs. Built in pre-programmed SWC retention. Retains Rear Seat Controls. Provides factory RSE activation. Does not retain SYNC. Check our other listing for the SYNC version. Factory amplified Systems will not fade as neither the aftermarket radio or the RP interface have the ability to control the amplifier? 2008 F-250/350/450: Not compatible with model trim XL (fleet vehicles). These vehicles do not have the necessary CAN bus signals. 2006 Lincoln Zephyr: Does not retain the THX amplifier. Military Bases / APO, FPO, PO Boxes. Only Pay the Duty once at a lower rate. UK, Europe, Germany, South America, Mexico. Asia, Australia, New Zealand, Japan. Powered by SixBit’s eCommerce Solution. The item “FORD Premium Stereo Radio Wire Harness w Steering Control CAN-BUS/ RAP/ VSS/ RSE” is in sale since Tuesday, August 7, 2012. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Interior\Dash Parts”. The seller is “vinyllust” and is located in Oceanside, California. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.
  • UPC: Does Not Apply
  • Manufacturer Part Number: Custom-Selected
  • Notes: Please Read Detailed Description
  • CustomTag_0: Notes
  • Brand: ABC-Install
  • Warranty: Yes

BMW Swap Convert N54 engine E90 E60 Harness/Wiring Adapter with CAN-BUS emulator

BMW Swap Convert N54 engine E90 E60 Harness/Wiring Adapter with CAN-BUS emulator

BMW Swap Convert N54 engine E90 E60 Harness/Wiring Adapter with CAN-BUS emulator

BMW Swap Convert N54 engine E90 E60 Harness/Wiring Adapter with CAN-BUS emulator

BMW Swap Convert N54 engine E90 E60 Harness/Wiring Adapter with CAN-BUS emulator

BMW N54 wiring harness adapter. With CAN-BUS emulator and. This Wiring Harness Adapter was developed to allow the installation / swap of an N54 engine with the original engine ECU, into any other BMW car. N54 is a Twin Turbo engine and is available on E90/E91/E92/E93, E60/E61, E82/E88 or E89. This Wiring Adapter is very easy to install. It is a plug and play solution. It is also included an OBD2 plug that you can use with your OBD tool to see live data, fault codes or even flash your ECU. You will find all the information needed and photos on the installation procedure included in this sale. This swap solution with this CAN BUS emulator was tested on a Dyno to make sure there is no power loss, the engine does not enter safe mode. The Engine ECU will store many fault codes due to a no CAN communication with all the others ECU´s (ABS, airbag, cluster, etc), so, we developed this CAN Emulator to simulate all the other e90´s ECU as well as the Junction Box to allow you to do diagnose, without our emulator you will not be able. So, Instead of having more than 20 fault codes, you will only have 5 faults codes. These are not possible to simulate. If you want you can delete these on the memory of the engine ECU with a help of a Chiptuner. The List of the fault codes are available on the instructions procedure. It is only possible to check the engine oil level using an e90´s cluster or diagnostic tool. However we developed on our emulator box a LED to allow you to check if the oil level is ok or not. To use our wiring harness adapter you must have from the new engine, the following SET/parts. Electronic gas pedal. Ignition key reader and the cable to CAS Module. All the wiring/plugs, related to the engine. We have a complete guide to help you removing all the wiring needed for this project. This type of engine ECU is not possible to delete EWS/IMMO. So, you must get CAS and key from the donor car. This product was developed using a N54B30 engine with MSD80 engine ECU, with manual transmission. Our wiring harness for N54 engine will be plug & play on your BMW E30 or E36, please inform us which car you have. Using our Kit all the information on your E30 or E36 cluster will work as stock. To build our wiring harness adaptors, we only use new electric components, original and high quality. We Speak English, Portuguese, French and German. Most items will be sent within 24 hours. Please check out our feedback! VAT invoice: all our items include a VAT invoice supplied with the goods. Please tell us your VAT number for correct invoice. The item “BMW Swap Convert N54 engine E90 E60 Harness/Wiring Adapter with CAN-BUS emulator” is in sale since Tuesday, April 9, 2019. This item is in the category “Vehicle Parts & Accessories\Car Parts\Other Car Parts”. The seller is “bruno_steering” and is located in Leiria. This item can be shipped worldwide.
  • Non-Domestic Product: No
  • BMW Swap old: BMW Swap old
  • Manufacturer Part Number: BLA015
  • Modified Item: No
  • Custom Bundle: No
  • Reference OE/OEM Number: BMWswap
  • Other Part Number: Swap E46
  • Brand: ANT Steering & Electronics