Ford 5.0 EFI Speed Density universal wiring harness 1985-1992

Ford 5.0 EFI Speed Density universal wiring harness 1985-1992

Sensor (NOT MAF) into your Cobra kit car, Muscle car, Street rod, Truck, 4×4, etc. You must use an ECM (sequential injector firing) from one of the Cars listed. The Truck/Bronco ECM (batch injector firing) is different and will. The Truck engines will have to replace your remote TFI distributor with a TFI attached distributor and mount 2 Oxygen sensors in the exhaust (Truck O2 sensor will not work). There are 3 versions of this harness (Throttle body on Passenger side, Throttle body on Drivers side and Truck/Bronco). Once every injector and sensor is plugged in, you will have 3 wires to hook up. Feed, Ignition feed and ground. It is built in the. With brand new OEM Ford connectors, 260 degree automotive grade GXL wire (thicker insulation than TXL wire). Harness can be used with long tube headers or stock exhaust manifolds. Harness is designed to mount the ECM under the dash (42 inches of wire from the back of the motor). Harness can be used with 5 speed manual, AOD, or any Non-computer controlled transmission. EGR eliminator is included and comes pre-installed. About the only upgrade you can add to the motor is Headers and exhaust improvements. If you wanted to change the. Heads, aftermarket intakes, throttle bodies, etc; I would not use this harness, the ECM cannot compensate for changes as well as a MAF system. This harness is made for the H. Firing order/Cam (1-3-7-2-6-5-4-8), but can be changed for Non-H. System includes: complete instructions, an assortment of 300 degree F wire loom, harness wrap and zip ties (not bare wire like other harnesses) to give it a finished look and protection. Manufactured by the Detail Zone (a division of Ron Francis Wiring) with RJM Technology. These are built right with quality parts from the correct manufacturers and quality checked for performance. Circuits are tested to assure quality. The item “Ford 5.0 EFI Speed Density universal wiring harness 1985-1992″ is in sale since Monday, July 01, 2013. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Air Intake & Fuel Delivery\Fuel Inject. Controls & Parts”. The seller is “qualityautospecialties” and is located in Chester, Pennsylvania. This item can be shipped to North, South, or Latin America, all countries in Europe, Australia, Japan, South africa, New Zealand.
  • Placement on Vehicle: Front
  • Warranty: Yes
  • Country of Manufacture: United States
  • Brand: The Detail Zone
  • Manufacturer Part Number: Cobra-75SD

New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA

New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA

New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA

New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA

New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA

New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA

If you are looking for a great quality stand-alone engine swap wiring harness, you have found it. Fuel Injection Connection has been dedicated to providing professionally constructed stand-alone electronic fuel injection wiring harnesses since 2004. We have been in the custom fuel Injection business since 1993. We strive for great customer service and have thousands of satisfied customers from all over the globe. You will be a satisfied customer as well. You wont need to though because these things are fantastic and they perform exactly as needed. Fuel Injection Connection specializes in General Motors (GM) wiring systems like TBI, TPI, LT-1, LS-1, LQ-9, LQ-4, E38 electronics from 2007 and up through 2014. Our harnesses are constructed with 100% all new Delphi manufactured connectors, lead soldered splices and thicker jacket GXL automotive wire. GXL wire has a thicker jacket that is more resistant to scuffing and abrasion and more important heat resistance. It is a chemically cross-linked gasoline rated wire that GM has used for years. Other harness manufacturers use thinner jacket (TXL) or even worse, NON automotive grade wire. We tell you this to help show that you can be assured that our harnesses are going to last for as long as you own it. Obviously this would not include anything outside of the scope of normal wear and tear. Our harnesses are also covered for you for that professional quality look and protection. We use the same corrugated slit loom as GM and not the lower heat stuff from auto parts stores. Each seam is taped and secured and these look great. Each harness that we offer has a little more than 4 feet of main trunk so that you mount the engine control module inside the cab or out of the way from the heat of the engine. Every harness has it own fuse block, Fuel pump relay, OB Diagnostic connector and wiring for misc. The installation of the wiring harness is a snap. Each of the connections in the harness are labeled and will only install at the plug that is designed for. 3 main wires is all you need to connect to run your engine. Battery Positive, Ignition ON and the fuel pump positive wires. There may be secondary wires as listed like SES, Tachometer etc. Thank you, it is a pleasure to serve you. TPI or Tuned Port Injection. Tuned Port Injection was used by General Motors on performance vehicles from 1985 through 1992. This wiring harness is designed to run on the TPI engines that came out of Camaros (F-body) and Corvette (Y-body) from 1985 through 1992. The wiring is designed for use with the 1227730 ECM from those models as well. The harnesses all have provision for 700R4 transmission that can be taped off if not used. We do not offer a harness for the 1227727 ecm. The donor vehicle will have the original coil wires needed to connect the coil and power up the distributor. Below is a list of the connections that are part of this TPI wiring harness that will plug into your equipment. ECM connectors (2 Black connectors, 1 24 pin and 1 32 pin) and (1 Yellow 32 pin) for 1227730 ecm. Fuel Pump Relay included in the harness (Includes Relay). OBD1 Data connector (for checking codes). 4 wire small connector that plugs into distributor. Oil Pressure sensor switch (not for gauge). Oxygen sensor (single wire). Coolant Temp signal for the ecm. Manifold Absolute Pressure or MAP sensor. Throttle Position Sensor (TPS). Idle Air Control Motor valve (IAC). 700R4 TCC Lock up. 8 Fuel injector connectors. A/C recognition wire (for aftermarket A/C systems). There are no emissions smog connection on this harness. (not needed on street rods). The item “New GM Engine Wiring Harness, 1990-Up Tuned Port Speed Density MAP TPI USA” is in sale since Thursday, July 13, 2017. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Ignition Systems\Other”. The seller is “fuelinjectionconnection” and is located in Golden, Colorado. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.
  • Brand: Fuel Injection Connection dot com
  • Manufacturer Part Number: FIC-00990
  • Interchange Part Number: FIC-00990
  • Other Part Number: FIC00990
  • Warranty: Yes
  • Country/Region of Manufacture: United States